Red-lion CUB5T User Manual download pdf

 LCD, REFLECTIVE OR RED/GREEN LED BACKLIGHTING

 0.46" (11.7 mm) HIGH DIGITS

 7-DIGIT BI-DIRECTIONAL TIMING CAPABILITY

 6-DIGIT CYCLE COUNTING CAPABILITY

 OPTIONAL RELAY OUTPUT MODULE

 OPTIONAL SERIAL COMMUNICATIONS MODULE (RS232 or RS485)

 SELECTABLE TIMER RANGES AND OPERATING MODES

 ELAPSED TIMER AND PRESET TIMER FUNCTIONALITY

 DISPLAY COLOR CHANGE CAPABILITY AT PRESET OUTPUT

 OPERATES FROM 9 TO 28 VDC POWER SOURCE

 NEMA 4X/IP65 SEALED FRONT BEZEL

MODEL CUB5T - MINIATURE ELECTRONIC PRESET TIMER

AND CYCLE COUNTER

GENERAL DESCRIPTION

The CUB5T provides the ultimate in timer flexibility, from its complete user

programming to the optional relay output and serial communications capability.

The meter functions as an Elapsed Timer or Preset Timer. It also has a built-in

Cycle Counter. The display can be toggled either manually or automatically

between the Timer and Cycle Counter values. With eight different input

operating modes and 18 selectable timer ranges, the meter can be programmed

for a wide variety of timing applications.

The CUB5T has an LCD display with 0.46" (11.7 mm) high digits. The LCD

is available in two versions, reflective (CUB5TR00) and backlight (CUB5TB00).

The backlight version is user selectable for red or green backlighting with

variable display intensity.

The Timer has two signal inputs and eight input operating modes. These

modes provide level active or edge triggered start/stop operation. A Display

Hold mode will display the elapsed time for one cycle, while the next cycle

continues timing internally. The Timer Reset modes will automatically reset the

timer value when a time start edge is applied to the input. This allows sequential

timing cycles without having to manually reset the Timer.

In addition to the Timer inputs, a programmable User Input is available to

perform a variety of meter functions. All inputs are current sinking (active low)

and accept a variety of logic and open-collector output signal sources. Relay and

switch contacts can also be used as signal sources, when the software input

debounce filter is enabled.

The capability of the CUB5T can be easily expanded with the addition of a

field installable option module. When the CUB5RLY0 relay output module is

added, the meter becomes a Preset Timer. The Setpoint Output can be assigned

to the Timer or Cycle Counter values, and configured to suit a variety of control

and alarm requirements. Serial communications capability for RS232 or RS485

is added with a serial option module (CUB5COM).

The CUB5T can be powered from an optional Red Lion Micro-Line/Sensor

Power Supply (MLPS), which attaches directly to the back of a CUB5T. The

MLPS is powered from an 85 to 250 VAC source and provides up to 400 mA to

drive the meter and sensors.

SAFETY SUMMARY

All safety related regulations, local codes and instructions that appear in this

literature or on equipment must be observed to ensure personal safety and to

prevent damage to either the instrument or equipment connected to it. If

equipment is used in a manner not specified by the manufacturer, the protection

provided by the equipment may be impaired.

Do not use this meter to directly command motors, valves, or other actuators

not equipped with safeguards. To do so can be potentially harmful to persons or

equipment in the event of a fault to the meter.

Bulletin No. CUB5T-D

Drawing No. LP0628

Released 07/12

Tel +1 (717) 767-6511

Fax +1 (717) 764-0839

www.redlion.net

CAUTION: Risk of Danger.

Read complete instructions prior to

installation and operation of the unit.

CAUTION: Risk of electric shock.

DIMENSIONS In inches (mm)

.13 (3.3)

(43.4)

1.71

2.95 (74.9)

SEL

.15 (3.8)

1.54 (39.1)

RST

(68 )

+.025

-.000

-0

1.29 (32.8)

2.68

-.000

1.30

(33 )

1 2 34

-0

+.024

ON ECE

Note: Recommended minimum clearance (behind the panel) for mounting clip installation is 2.15" (54.6) H x 3.00" (76.2) W.

US LISTED

51EB

IND. CONT. EQ.

1 2 3 4 5 6 ... 15 16

Summary of Contents

Page 1 - AND CYCLE COUNTER

1 LCD, REFLECTIVE OR RED/GREEN LED BACKLIGHTING 0.46" (11.7 mm) HIGH DIGITS 7-DIGIT BI-DIRECTIONAL TIMING CAPABILITY 6-DIGIT CYCLE COUNTI

Page 2 - ORDERING INFORMATION

10SAVE will restore the output to the same state it was at before the meter was powered down. ON will activate the output at power up. OFF will deacti

Page 3 - 2.0 DIP SWITCHES

11DATA BITABBREVIATED PRINTING PRINT OPTIONSPARITY BITMETER ADDRESS300 1200600 24001920038400480096007-bit 8-bitNO Odd EVENNO YESNO YESModule 5 is the

Page 4 - 3.0 INSTALLING PLUG-IN CARDS

Command String ConstructionThe command string must be constructed in a specific sequence. The meter does not respond with an error message to illegal

Page 5 - 4.4 SETPOINT (OUTPUT) WIRING

13Command Response TimeThe meter can only receive data or transmit data at any one time (half-duplex operation). During RS232 transmissions, the meter

Page 6 - 6.0 PROGRAMMING THE METER

14This page intentionally left blank.

Page 7 - 1-INPUt)

15RSTBacklight Unit OnlyExitProgramming SELSELSELSELSELRSTRSTRSTRSTSELRSTBacklight Unit OnlyTimer StartValue Timer InputFilter Timer InputOperation Ti

Page 8 - 2-Count)

LIMITED WARRANTYThe Company warrants the products it manufactures against defects in materials and workmanship for a period limited to two years from

Page 9 - 3-dSPLAY)

1. DISPLAY: 8 digit LCD 0.46" (11.7 mm) high digitsCUB5TR00: Reflective LCD with full viewing angleCUB5TB00: Selectable transmissive red or green

Page 10 - 4-SEtPt)

3ADDING OPTION CARDSThe CUB5T meters can be fitted with optional relay card and/or serial communications cards. The details for the plug-in cards can

Page 11 - FACTORY

WIRING OVERVIEWElectrical connections are made via screw-clamp terminals located on the back of the meter. All conductors should conform to the meter’

Page 12 - Receiving Data From The Meter

54.1 POWER WIRINGINP COMMUSR+9-28 VDCINP BINP APWR COMMON+-DC Power+9 to +28 VDC: +VDCPower Common: -VDC4.2 USER INPUT WIRINGINP COMMUSR+9-28 VDCINP

Page 13 - Communication Format

6PROGRAMMING MODE ENTRY (SEL KEY)It is recommended all programming changes be made off line, or before installation. The meter normally operates in th

Page 14

Timer Input OperationTimer Input FilterTimer Run State At Power-upTiming DirectionTimer Start ValueFlash Timer AnnunciatorTimer Reset At Power-upTimer

Page 15 - Press and hold SEL key to

86.2 MODULE 2 - CYCLE COUNTER PARAMETERS (2-Count)SELCycle CounterCount SourceCycle CounterEnableCycle CounterCountingDirectionCycle CounterStart Val

Page 16 - LIMITED WARRANTY

9The yES selection allows the SEL button to toggle between the timer and cycle counter displays.FRONT PANEL DISPLAY SELECT ENABLE (SEL)6.3 MODULE 3 -