Red-lion PAX2D User Manual Page 16
- Page / 36
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
16
SELECT PARAMETER LIST
Two lists of values are available to allow the user to switch between two sets
of Setpoints, Scale Factors, Counter Load values and Units mnemonics. The two
lists are List A and List B. If a user input is used to select the list then List A is
selected when the user input is not active and List B is selected when the user
input is active (maintained action). If a front panel key is used to select the list
then the list will toggle for each key press (momentary action). The display will
only indicate which list is active when the list is changed.
A submenu is used to select whether the programmed Units Mnemonics are
included in the List function. Select YES in the submenu to have different Units
Mnemonics for List A and List B. Select NO to display the same mnemonics
regardless of the list selected.
To program the values for List A and List B, first complete the programming
of all the parameters with List A selected. Exit programming and switch to List
B. Re-enter programming and program the desired values for the parameters
included in the List.
DISPLAY DESCRIPTION FACTORY
UNItS
Units Mnemonics
NO
PRINT REQUEST
The meter issues a block print through the serial port when activated, and the
serial type is set to rLC. The data transmitted during a print request and the serial
type is programmed in Port (Serial) module. If the user input is still active after
the transmission is complete (about 100 msec), an additional transmission
occurs. As long as the user input is held active, continuous transmissions occur.
PRINT REQUEST AND RESET DISPLAYS
The meter issues a block print through the serial port when activated just like
the Print Request function. In addition, when activated (momentary action), the
meter performs a reset of the displays configured as YES in the sublist. Both the
Print and Reset actions will only function when the serial type parameter (tYPE)
is set to Red Lion protocol (rLC).
DISPLAY DESCRIPTION FACTORY
Cnt A
Counter A
NO
Cnt b
Counter B
NO
Cnt C
Counter C
NO
Hi
Maximum
NO
Lo
Minimum
NO
MAINTAINED (LEVEL) RESET AND INHIBIT
The meter performs a reset and inhibits the displays configured as YES in the
sublist, as long as activated (maintained action).
DISPLAY DESCRIPTION FACTORY
Cnt A
Counter A
NO
Cnt b
Counter B
NO
Cnt C
Counter C
NO
Hi
Maximum
NO
Lo
Minimum
NO
MOMENTARY (EDGE) RESET
When activated (momentary action), the meter resets the displays configured
as YES in the sublist.
DISPLAY DESCRIPTION FACTORY
Cnt A
Counter A
NO
Cnt b
Counter B
NO
Cnt C
Counter C
NO
Hi
Maximum
NO
Lo
Minimum
NO
INHIBIT
The meter inhibits the displays configured as YES in the sublist, as long as
activated (maintained action).
DISPLAY DESCRIPTION FACTORY
Cnt A
Counter A
NO
Cnt b
Counter B
NO
Cnt C
Counter C
NO
Hi
Maximum
NO
Lo
Minimum
NO
STORE DISPLAY
The meter holds (freezes) the displays configured as YES in the sublist, as long
as activated (maintained action). Internally, the counters and max and min values
continue to update.
DISPLAY DESCRIPTION FACTORY
Cnt A
Counter A
NO
Cnt b
Counter B
NO
Cnt C
Counter C
NO
Hi
Maximum
NO
Lo
Minimum
NO
STORE AND RESET DISPLAY
The meter holds (freezes) the displays and then performs a reset of the
displays configured as YES in the sublist, as long as activated (maintained
action).
DISPLAY DESCRIPTION FACTORY
Cnt A
Counter A
NO
Cnt b
Counter B
NO
Cnt C
Counter C
NO
Hi
Maximum
NO
Lo
Minimum
NO
SETPOINT DEACTIVATE (RESET) MAINTAINED (LEVEL)
The meter deactivates (resets) the setpoint outputs configured as YES in the
sublist, as long as activated (maintained action).
DISPLAY DESCRIPTION FACTORY
S1
Setpoint 1
NO
S2
Setpoint 2
NO
S3
Setpoint 3
NO
S4
Setpoint 4
NO
USEr-n
LISt
USr
Fn
LISt
FNC
USEr-n
Print
USr
Fn
Print
FNC
USEr-n
Pr-rSt
USr
Fn
Pr-rSt
FNC
USEr-n
RSt-L
USr
Fn
RSt-L
FNC
USEr-n
RSt-E
USr
Fn
RSt-E
FNC
USEr-n
Inhibt
USr
Fn
Inhibt
FNC
USEr-n
StorE
USr
Fn
StorE
FNC
USEr-n
St-rSt
USr
Fn
St-rSt
FNC
USEr-n
SPr-L
USr
Fn
SPr-L
FNC
- DESCRIPTION 1
- SAFETY SUMMARY 1
- DIMENSIONS In inches (mm) 1
- Table Of COnTenTs 2
- Ordering infOrmaTiOn 2
- OpTiOnal plug-in OuTpuT Cards 4
- 1.0 insTalling The meTer 5
- 2.0 seTTing The dip swiTChes 5
- 3.0 insTalling plug-in Cards 6
- 4.0 wiring The meTer 6
- 4.1 POWER WIRING 7
- 4.2 INPUT SIGNAL WIRING 7
- 7 8 9 10 8
- 6.0 prOgramming The paX2d 9
- PROGRAMMING MODE EXIT 10
- PROGRAMMING TIPS 10
- Prescaler Output Value = 0.25 11
- RATE INPUT PARAMETERS (RAtE) 12
- SELECTION MODE DESCRIPTION 13
- OuTpuT parameTers (OUtPUt) 17
- SELECTION DISPLAY VALUE 18
- SELECTION ACTION 19
- ANALOG OUTPUT TYPE 20
- ANALOG OUTPUT ASSIGNMENT 20
- ANALOG LOW SCALE VALUE 20
- ANALOG HIGH SCALE VALUE 20
- LINE 1 PARAMETERS (LINE 1) 21
- LINE 2 PARAMETERS (LINE 2) 22
- LINE 2 UNITS MNEMONIC(S) 23
- PROGRAMMING SECURITY CODE 23
- USB PORT PARAMETERS (USb) 24
- SUPPORTED FUNCTION CODES 25
- SUPPORTED EXCEPTION CODES 25
- COMMUNICATION FORMAT 29
- COMMAND RESPONSE TIME 29
- Timing Diagrams 29
- To calibrate, connect a 30
- TROUBLESHOOTING 31
- LIMITED WARRANTY 36
Related products and manuals for Computer Accessories Red-lion PAX2D
(74 pages)© 2020, manymanuals.com. All rights reserved. | 0.066 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals