Red-lion TCU User Manual Page 94
- Page / 104
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Analog Output Calibration (ANCL) (Cont’d)
0to10VDC
Press PAR until ANCL appears in the display. Connect a p recision
voltmeter (0.1% accuracy) to rear terminals (+) #11 and (-) #12.
Display Parameter Description/Comments
ANC1 Analog output 0 VDC
code value
Observe voltage reading. If 0.00 VDC,
press PAR. If not equal, modify existing
code value using up and down buttons to
achieve 0.00 VDC. Press PAR.
ANC2 Analog output 10
VDC code value
Observe voltage reading. If 10.00 VDC,
Press PAR. If not equal, modify existing
code value using up and down buttons to
achieve 10.00 VDC. Press PAR.
Second Analog Input Calibration (2CAL)
The signals applied to the Second analog Input for calibration depend on
the type of model. Second Analog Input, Heater Current Monitor, and
Motorized Valve Positioner represent the models for which unique
calibration signals are required.
Second Analog Input (Remote Setpoint)
Connect precision DC milliampere source (0.01% accuracy) to rear
terminals labeled Second Analog Input, 4-20 mA+ and 4-20 mA-.
Display Parameter Description/Comments
StP1 0.00 mA step Apply 0.00 mA DC, press PAR.
StP2 5.00 mA step Apply 5.00 mA DC, press PAR.
StP3 10.00 mA step Apply 10.00 mA DC, press PAR.
StP4 15.00 mA step Apply 15.00 mA DC, press PAR.
StP5 20.00 mA step Apply 20.00 mA DC, press PAR.
Heater Current Monitor
Connect precision AC milliampere source (0.1% accuracy) to rear
terminals labeled Second Analog Input, CT+ And CT-.
Display Parameter Description/Comments
StP1 0.0 mA step Apply 0.0 mA AC 60 Hz, press PAR.
StP2 25.0 mA step Apply 25.0 mA AC 60 Hz, press PAR.
StP3 50.0 mA step Apply 50.0 mA AC 60 Hz, press PAR.
StP4 75.0 mA step Apply 75.0 mA AC 60 Hz, press PAR.
StP5 100.0 mA step Apply 100.0 mA AC 60 Hz, press PAR.
Motorized Valve Positioner
Construct a precision resistor
divider network consisting of four
250W 0.1% tolerance resistors
connected in series as shown in
Figure 45, Resistor Divider.
Connect one end of the resistor
string to the rear terminal labeled
Slidewire Feedback Inputs,
Comm. and the other end to
Excitation. The connection to the
Wiper terminal comes from
different points of the resistor
string.
Display Parameter Description/Comments
StP1 0.0% step Connect wiper input to 0% point of divider
(Comm.), wait 10 seconds, press PAR.
StP2 25.0% step Connect wiper input to 25% point of divider,
wait 10 seconds, press PAR.
StP3 50.0% step Connect wiper input to 50% point of divider,
wait 10 seconds, press PAR.
StP4 75.0% step Connect wiper input to 75% point of divider,
wait 10 seconds, press PAR.
StP5 100.0% step Connect wiper input to 100% point of divider
(Excitation), wait 10 seconds press PAR.
86
Figure 45, Resistor Divider
- THE TEMPERATURE 1
- CONTROLLER 1
- US LISTED 2
- Table of Contents 3
- GENERAL DESCRIPTION 9
- SAFETY SUMMARY 10
- Installation Environment 11
- Standard Unit Installation 11
- Removing Bezel Assembly 13
- Installing Bezel Assembly 13
- Unit Removal Procedure 13
- Output Modules 14
- Select Input Sensor Type 15
- Select AC Power (115/230 VAC) 15
- EMC INSTALLATION GUIDELINES 16
- Wiring Connections 16
- error of 2.5°C/ohm of 17
- FRONT PANEL DESCRIPTION 20
- OPERATION OVERVIEW 21
- Configuration Of Parameters 23
- Parameter Entry 24
- Normal Display Mode 24
- UNPROTECTED PARAMETER MODE 25
- PROTECTED PARAMETER MODE 27
- Front Panel Program Disable 28
- HIDDEN FUNCTION MODE 29
- Input Module (1- In) 30
- Output Module (2-OP) 33
- Lockouts Module (3-LC) 36
- from the temperature 41
- Communication Format 56
- Sending Commands And Data 56
- Receiving Data 59
- PC (Cont’d) 62
- Serial Connections 62
- HEATER CURRENT MONITOR OPTION 65
- VALVE POSITION OPTION 66
- Velocity Mode Valve Control 67
- SECOND ANALOG INPUT OPTION 68
- PID CONTROL 71
- Derivative Time 72
- PID Adjustments 72
- PID Adjustments (Cont’d) 73
- ON/OFF CONTROL 74
- AUTO-TUNE 76
- Initiate Auto-Tune 77
- Plastics Extruder Application 79
- APPENDIX “D” - MANUAL TUNING 89
- Closed Loop Cycling Method 90
- APPENDIX “E” - CALIBRATION 91
- Second Input Check 92
- Heater Current Monitor Check 92
- Second Analog Input Check 92
- Valve Positioner Check 92
- Calibration 92
- UNIT NUMBER 95
- CONFIGURE INPUT 95
- CONFIGURE OUTPUT 95
- CONFIGURE LOCKOUTS 96
- CONFIGURE ALARMS 96
- CONFIGURE COOLING 96
- CONFIGURE SECOND ANALOG INPUT 97
- CONFIGURE VALVE POSITIONER 97
- CONTROLLER OPERATING MODE 97
- HEATER CURRENT MONITOR MODELS 98
- LIMITED WARRANTY 103
- TCU/IM - N 02/13 104
- DRAWING NO. LP0235 104
Related products and manuals for Hardware Red-lion TCU
Hardware Red-lion PSC User Manual
(8 pages)
(8 pages)
Hardware Red-lion TSC User Manual
(92 pages)
(92 pages)
Hardware Red-lion PCU User Manual
(96 pages)
(96 pages)
Hardware Red-lion TLA User Manual
(16 pages)
(16 pages)
Hardware Red-lion IFMA User Manual
(8 pages)
(8 pages)
Hardware Red-lion ITMS User Manual
(16 pages)
(16 pages)
Hardware Red-lion IAMS User Manual
(4 pages)
(4 pages)
Hardware Red-lion IFMR User Manual
(8 pages)
(8 pages)
Hardware Red-lion AIMI User Manual
(1 pages)
(1 pages)
Hardware Red-lion IAMA User Manual
(8 pages)
(8 pages)
Hardware Red-lion IAMA0006 User Manual
(4 pages)
(4 pages)
Hardware Red-lion IRMA User Manual
(8 pages)
(8 pages)
Hardware Red-lion ITMA User Manual
(8 pages)
(8 pages)
Hardware Red-lion IAMS User Manual
(86 pages)
(86 pages)
Hardware Red-lion NT100 User Manual
(4 pages)
(4 pages)
Hardware Red-lion ICM8 User Manual
(8 pages)
(8 pages)
Hardware Red-lion GCM232 User Manual
(4 pages)
(4 pages)
Hardware Red-lion GCM422 User Manual
(4 pages)
(4 pages)
Hardware Red-lion ICM4 User Manual
(4 pages)
(4 pages)
© 2020, manymanuals.com. All rights reserved. | 2.436 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals