Red-lion TSC User Manual Page 50
- Page / 92
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
The Programming Data For The Example:
Input Module 1 (1-IN)
Mnemonic Value Description
InPt P1rH User input is programmed for run/pause
operation
Alarm Module 4 (4-AL)
Mnemonic Value Description
Act 1 P-Ev Program alarm 1 for timed event output
Act 2 P-Ev Program alarm 2 for timed event output
Profile Module 8 (8-Pr)
Mnemonic Value Description
P1CC 1 Cycle profile once after started
P1Ln no Do not link to profile 2 when done
P1St Cont Continue profile operation when power is restored
P1Eb 8 Delay mode if temperature deviates ± 8°
P1r1 4.0 Ramp rate 1 is 4.0/minute
P1L1 350 Setpoint level 1 is 350
P1H1 20.0 Hold time 1 is 20.0 minutes
P1r2 3.0 Ramp rate 2 is 3.0/minute
P1L2 500 Setpoint level 2 is 500
P1H2 60.0 Hold time 2 is 60.0 minutes
P1r3 0.0 Ramp rate 3 is step ramp
P1L3 750 Setpoint level 3 is 750
P1H3 0.0 Hold time 3 is skipped
P1r4 7.5 Ramp rate 4 is 7.5/minute
P1L4 875 Setpoint Level 4 is 875
P1H4 150.0 Hold time 4 is 150.0 minutes
P1r5 10.0 Ramp rate 5 is 10.0/minute
P1L5 250 Setpoint level 5 is 250
P1H5 0.0 Hold time 5 is skipped
P1r6 3.8 Ramp rate 6 is 3.8/minute
P1L6 100 Setpoint level 6 is 100
P1H6 0.0 Hold time 6 is skipped
P1r7 -0.1 Ramp rate 7 ends profile
Profile Module 8 (8-Pr) (Cont’d)
Mnemonic Value Description
P1 1 1F2F Keep both outputs off
P1 2 1F2F Keep both outputs off
P1 3 1F2F Keep both outputs off
P1 4 1F2F Keep both outputs off
P1 5 1F2F Keep both outputs off
P1 6 1F2F Keep both outputs off
P1 7 1F2F Keep both outputs off
P1 8 1F2F Keep both outputs off
P1 9 1N2F Turn on auxiliary cooling
P110 1F2F Turn off auxiliary cooling
P111 1F2F Keep both outputs off
P112 1F2N Turn on end of profile signal
FACTORY SERVICE OPERATIONS MODULE (9-FS)
The Factory Service Operations are programming functions which are
performed on an infrequent basis. They include: controller calibration, and reset
programming to factory configuration setting. Given the ramifications of these
operations, access to each is protected by an access code number. Entering code
66 will restore all parameters to factory settings, the unit will indicate the
operation after the PAR button is pressed, by displaying “rSEt” in the lower
display momentarily. The calibration operations are detailed in Appendix “F”.
Note: Entering code 66 will reset all programming parameters to the
factory settings.
-48-
- THE TEMPERATURE SETPOINT 1
- CONTROLLER 1
- US LISTED 2
- Table of Contents 3
- GENERAL DESCRIPTION 8
- SAFETY SUMMARY 9
- INSTALLATION ENVIRONMENT 9
- STANDARD UNIT INSTALLATION 9
- UNIT REMOVAL PROCEDURE 11
- REMOVING BEZEL ASSEMBLY 11
- INSTALLING BEZEL ASSEMBLY 11
- OUTPUT MODULES 12
- SELECT INPUT SENSOR TYPE 13
- WIRING CONNECTIONS 14
- SELECT AC POWER (115/230 VAC) 14
- EMC INSTALLATION GUIDELINES 14
- FRONT PANEL DESCRIPTION 16
- OPERATION OVERVIEW 17
- PROFILE OPERATING MODES 18
- CONTROLLING A PROFILE 20
- CONFIGURATION OF PARAMETERS 24
- PARAMETER ENTRY 25
- NORMAL DISPLAY MODE 25
- Profile Status Description 26
- UNPROTECTED PARAMETER MODE 27
- PROTECTED PARAMETER MODE 28
- FRONT PANEL PROGRAM DISABLE 29
- HIDDEN FUNCTION MODE 30
- INPUT MODULE (1- IN) 31
- INPUT MODULE (1- IN) (Cont’d) 32
- OUTPUT MODULE (2-OP) 34
- OP - Percent output power 35
- SP - Process setpoint value 35
- LOCKOUTS MODULE (3-LC) 36
- (OPTIONAL) 41
- CONTROL POINTS MODULE (7-CP) 44
- PROFILES MODULE (8-PR) 44
- (correction shift) 51
- Yes/no (no) 56
- COMMUNICATION FORMAT 60
- SENDING COMMANDS AND DATA 60
- RECEIVING DATA 62
- SERIAL CONNECTIONS 64
- PID CONTROL 66
- INTEGRAL TIME (Cont’d) 67
- DERIVATIVE TIME 67
- PID ADJUSTMENTS 67
- PROCESS RESPONSE EXTREMES 68
- ON/OFF CONTROL 69
- AUTO-TUNE 71
- AUTO-TUNE (Cont’d) 72
- DIMENSIONS In inches (mm) 74
- “....” or “-...” IN DISPLAY 78
- OUTPUT LEAKAGE CURRENT 81
- APPENDIX “D” - MANUAL TUNING 82
- CLOSED LOOP CYCLING METHOD 83
- APPENDIX “E” - CALIBRATION 84
- CALIBRATION 85
- OP Output Power 87
- SPLO Setpoint Lower Limit 87
- Configure Control Points 88
- Configure Profiles 88
- Controller Operating Mode 88
- LIMITED WARRANTY 91
- TSC/IM - B 5/05 92
- DRAWING NO. LP0275 92
Related products and manuals for Hardware Red-lion TSC
Hardware Red-lion PCU User Manual
(96 pages)
(96 pages)
Hardware Red-lion TLA User Manual
(16 pages)
(16 pages)
Hardware Red-lion IFMA User Manual
(8 pages)
(8 pages)
Hardware Red-lion ITMS User Manual
(16 pages)
(16 pages)
Hardware Red-lion IAMS User Manual
(4 pages)
(4 pages)
Hardware Red-lion IFMR User Manual
(8 pages)
(8 pages)
Hardware Red-lion AIMI User Manual
(1 pages)
(1 pages)
Hardware Red-lion IAMA User Manual
(8 pages)
(8 pages)
Hardware Red-lion IAMA0006 User Manual
(4 pages)
(4 pages)
Hardware Red-lion IRMA User Manual
(8 pages)
(8 pages)
Hardware Red-lion ITMA User Manual
(8 pages)
(8 pages)
Hardware Red-lion IAMS User Manual
(86 pages)
(86 pages)
Hardware Red-lion NT100 User Manual
(4 pages)
(4 pages)
Hardware Red-lion ICM8 User Manual
(8 pages)
(8 pages)
Hardware Red-lion GCM232 User Manual
(4 pages)
(4 pages)
Hardware Red-lion GCM422 User Manual
(4 pages)
(4 pages)
Hardware Red-lion ICM4 User Manual
(4 pages)
(4 pages)
Hardware Red-lion ICM5 User Manual
(4 pages)
(4 pages)
Hardware Red-lion RLY5 User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 0.593 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals