Red-lion TSC User Manual Page 20
- Page / 92
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
CONTROLLING A PROFILE
Profile Start Operation
A profile always starts at the first ramp phase and the setpoint value ramps
from the current temperature value. The profile can be programmed to ramp
from a known setpoint value (see Ramp Phase section). Link-started profiles
use the last target setpoint level as the starting point. A profile is started from
the off mode, which places the controller into the run mode. To re-start a
running profile from the beginning, it is necessary to first stop the profile.
Start Operation From The Profile Control Status Display
1. Verify the profile control status display (P-CS) is enabled in lockout
programming.
2. Profile must be in the off mode (no profiles running).
3. Press and hold “up” button for three seconds until “Pr-1” appears.
4. Select the desired profile by using the “up/down” buttons.
5. Press the “PAR” button to start the selected profile. The unit displays
“Strt” in the secondary display and starts the profile. If the “PAR”
button is not pressed within five seconds, no action is taken.
Start Operation From The Hidden Mode
1. Verify profile access (PrAC) in the hidden mode is enabled in lockout
programming.
2. Profile must be in the off mode (no profiles running).
3. Press and hold the “PAR” button for three seconds to enter the
hidden mode.
4. Scroll to “Prun” (if necessary) by pressing the “PAR” button.
5. When “Prun” is displayed, use the “up/down” buttons to select the
desired profile (Pr-1, Pr-2, Pr-3, or Pr-4).
6. Press the “PAR” button to start the selected profile. The unit displays
“End” in the secondary display and starts the profile. If a selection is
not made within ten seconds, no action is taken.
Start Operation Using The User Input
The user input can only start profile #1.
User Input Selected For Run/Stop (P1rS):
A low to high transition at terminal # 7 always starts profile 1.
User Input Selected For Run/Pause (P1rH):
A low to high transition at terminal # 7 starts profile 1, if no profiles
are in the pause mode.
Note: Refer to input module 1, user input section, for more details.
Start Operation On Power-Up
If power is interrupted or removed from the unit, the profile can be
programmed to automatically start when power is restored. In the Setpoint
Profiles Module (8-Pr), a profile can be programmed to automatically re-start
on power-up. The “Strt” option must selected for each profile (see power cycle
status parameter for details).
Start Operation Via The RS-485 Serial Option
Any profile can be started via the serial communications option. Transmit the
unit address, command letter with the value identifier and the desired profile
number via the serial port (see serial communication section for details).
Shown below is a typical command string.
Start profile 2 of TSC unit 6.
N6CU2*
-18-
- THE TEMPERATURE SETPOINT 1
- CONTROLLER 1
- US LISTED 2
- Table of Contents 3
- GENERAL DESCRIPTION 8
- SAFETY SUMMARY 9
- INSTALLATION ENVIRONMENT 9
- STANDARD UNIT INSTALLATION 9
- UNIT REMOVAL PROCEDURE 11
- REMOVING BEZEL ASSEMBLY 11
- INSTALLING BEZEL ASSEMBLY 11
- OUTPUT MODULES 12
- SELECT INPUT SENSOR TYPE 13
- WIRING CONNECTIONS 14
- SELECT AC POWER (115/230 VAC) 14
- EMC INSTALLATION GUIDELINES 14
- FRONT PANEL DESCRIPTION 16
- OPERATION OVERVIEW 17
- PROFILE OPERATING MODES 18
- CONTROLLING A PROFILE 20
- CONFIGURATION OF PARAMETERS 24
- PARAMETER ENTRY 25
- NORMAL DISPLAY MODE 25
- Profile Status Description 26
- UNPROTECTED PARAMETER MODE 27
- PROTECTED PARAMETER MODE 28
- FRONT PANEL PROGRAM DISABLE 29
- HIDDEN FUNCTION MODE 30
- INPUT MODULE (1- IN) 31
- INPUT MODULE (1- IN) (Cont’d) 32
- OUTPUT MODULE (2-OP) 34
- OP - Percent output power 35
- SP - Process setpoint value 35
- LOCKOUTS MODULE (3-LC) 36
- (OPTIONAL) 41
- CONTROL POINTS MODULE (7-CP) 44
- PROFILES MODULE (8-PR) 44
- (correction shift) 51
- Yes/no (no) 56
- COMMUNICATION FORMAT 60
- SENDING COMMANDS AND DATA 60
- RECEIVING DATA 62
- SERIAL CONNECTIONS 64
- PID CONTROL 66
- INTEGRAL TIME (Cont’d) 67
- DERIVATIVE TIME 67
- PID ADJUSTMENTS 67
- PROCESS RESPONSE EXTREMES 68
- ON/OFF CONTROL 69
- AUTO-TUNE 71
- AUTO-TUNE (Cont’d) 72
- DIMENSIONS In inches (mm) 74
- “....” or “-...” IN DISPLAY 78
- OUTPUT LEAKAGE CURRENT 81
- APPENDIX “D” - MANUAL TUNING 82
- CLOSED LOOP CYCLING METHOD 83
- APPENDIX “E” - CALIBRATION 84
- CALIBRATION 85
- OP Output Power 87
- SPLO Setpoint Lower Limit 87
- Configure Control Points 88
- Configure Profiles 88
- Controller Operating Mode 88
- LIMITED WARRANTY 91
- TSC/IM - B 5/05 92
- DRAWING NO. LP0275 92
Related products and manuals for Hardware Red-lion TSC
Hardware Red-lion PCU User Manual
(96 pages)
(96 pages)
Hardware Red-lion TLA User Manual
(16 pages)
(16 pages)
Hardware Red-lion IFMA User Manual
(8 pages)
(8 pages)
Hardware Red-lion ITMS User Manual
(16 pages)
(16 pages)
Hardware Red-lion IAMS User Manual
(4 pages)
(4 pages)
Hardware Red-lion IFMR User Manual
(8 pages)
(8 pages)
Hardware Red-lion AIMI User Manual
(1 pages)
(1 pages)
Hardware Red-lion IAMA User Manual
(8 pages)
(8 pages)
Hardware Red-lion IAMA0006 User Manual
(4 pages)
(4 pages)
Hardware Red-lion IRMA User Manual
(8 pages)
(8 pages)
Hardware Red-lion ITMA User Manual
(8 pages)
(8 pages)
Hardware Red-lion IAMS User Manual
(86 pages)
(86 pages)
Hardware Red-lion NT100 User Manual
(4 pages)
(4 pages)
Hardware Red-lion ICM8 User Manual
(8 pages)
(8 pages)
Hardware Red-lion GCM232 User Manual
(4 pages)
(4 pages)
Hardware Red-lion GCM422 User Manual
(4 pages)
(4 pages)
Hardware Red-lion ICM4 User Manual
(4 pages)
(4 pages)
Hardware Red-lion ICM5 User Manual
(4 pages)
(4 pages)
Hardware Red-lion RLY5 User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 2.689 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals